nvic.h

[Stub] support.

Library Documentation

Nested vector interrupt controller support.

Defines

NVIC_BASE

NVIC register map base pointer.

Enums

nvic_irq_num enum

Interrupt vector table interrupt numbers.

Each enumerator is the position of the corresponding interrupt in the vector table.

Values:

• NVIC_NMI = -14 -

  Non-maskable interrupt.

• NVIC_HARDFAULT = -13 -

  Hard fault (all class of fault).

• NVIC_MEM_MANAGE = -12 -

  Memory management.

• NVIC_BUS_FAULT = -11 -

  Bus fault: prefetch fault, memory access fault.

• NVIC_USAGE_FAULT = -10 -

  Usage fault: Undefined instruction or illegal state.

• NVIC_SVC = -5 -

  System service call via SWI insruction.

• NVIC_DEBUG_MON = -4 -

  Debug monitor.

• NVIC_PEND_SVC = -2 -

  Pendable request for system service.

• NVIC_SYSTICK = -1 -

  System tick timer.

• NVIC_WWDG = 0 -

  Window watchdog interrupt.

• NVIC_PVD = 1 -

  PVD through EXTI line detection.

• NVIC_TAMPER = 2 -

  Tamper.

• NVIC_RTC = 3 -

  Real-time clock.

• NVIC_FLASH = 4 -

  Flash.

• NVIC_RCC = 5 -

  Reset and clock control.

• NVIC_EXTI0 = 6 -

  EXTI line 0.

• NVIC_EXTI1 = 7 -

  EXTI line 1.

• NVIC_EXTI2 = 8 -

  EXTI line 2.

• NVIC_EXTI3 = 9 -

  EXTI line 3.

• NVIC_EXTI4 = 10 -

  EXTI line 4.

• NVIC_DMA_CH1 = 11 -

  DMA1 channel 1.

• NVIC_DMA_CH2 = 12 -

  DMA1 channel 2.

• NVIC_DMA_CH3 = 13 -

  DMA1 channel 3.

• NVIC_DMA_CH4 = 14 -

  DMA1 channel 4.

• NVIC_DMA_CH5 = 15 -

  DMA1 channel 5.

• NVIC_DMA_CH6 = 16 -

  DMA1 channel 6.

• NVIC_DMA_CH7 = 17 -

  DMA1 channel 7.

• NVIC_ADC_1_2 = 18 -

  ADC1 and ADC2.

• NVIC_USB_HP_CAN_TX = 19 -

  USB high priority or CAN TX.

• NVIC_USB_LP_CAN_RX0 = 20 -

  USB low priority or CAN RX0.

• NVIC_CAN_RX1 = 21 -

  CAN RX1.

• NVIC_CAN_SCE = 22 -

  CAN SCE.

• NVIC_EXTI_9_5 = 23 -

  EXTI line [9:5].

• NVIC_TIMER1_BRK = 24 -

  Timer 1 break.

• NVIC_TIMER1_UP = 25 -

  Timer 1 update.

• NVIC_TIMER1_TRG_COM = 26 -

  Timer 1 trigger and commutation.

• NVIC_TIMER1_CC = 27 -

  Timer 1 capture/compare.

• NVIC_TIMER2 = 28 -

  Timer 2.

• NVIC_TIMER3 = 29 -

  Timer 3.

• NVIC_TIMER4 = 30 -

  Timer 4.

• NVIC_I2C1_EV = 31 -

  I2C1 event.

• NVIC_I2C1_ER = 32 -

  I2C1 error.

• NVIC_I2C2_EV = 33 -

  I2C2 event.

• NVIC_I2C2_ER = 34 -

  I2C2 error.

• NVIC_SPI1 = 35 -

  SPI1.

• NVIC_SPI2 = 36 -

  SPI2.

• NVIC_USART1 = 37 -

  USART1.

• NVIC_USART2 = 38 -

  USART2.

• NVIC_USART3 = 39 -

  USART3.

• NVIC_EXTI_15_10 = 40 -

  EXTI line [15:10].

• NVIC_RTCALARM = 41 -

  RTC alarm through EXTI line.

• NVIC_USBWAKEUP = 42 -

  USB wakeup from suspend through EXTI line.

• NVIC_TIMER8_BRK = 43 -

  Timer 8 break.

• NVIC_TIMER8_UP = 44 -

  Timer 8 update.

• NVIC_TIMER8_TRG_COM = 45 -

  Timer 8 trigger and commutation.

• NVIC_TIMER8_CC = 46 -

  Timer 8 capture/compare.

Functions

void nvic_init(uint32 vector_table_address, uint32 offset)

Initialize the NVIC.

Parameters:

• vector_table_address -

  Vector table base address.

• offset -

  Offset from vector_table_address. Some restrictions apply to the use of nonzero offsets; see ST RM0008 and the ARM Cortex M3 Technical Reference Manual.

void nvic_set_vector_table(uint32 address, uint32 offset)

Reset the vector table address.

void nvic_irq_set_priority(nvic_irq_num irqn, uint8 priority)

Nested interrupt controller routines.

Set interrupt priority for an interrupt line Note: The STM32 only implements 4 bits of priority, ignoring the lower 4 bits. This means there are only 16 levels of priority. Bits[3:0] read as zero and ignore writes.

Parameters:

• irqn -

  device to set

• priority -

  Priority to set, 0 being highest priority and 15 being lowest.

void nvic_globalirq_enable()

Enables interrupts and configurable fault handlers (clear PRIMASK).

void nvic_globalirq_disable()

Disable interrupts and configurable fault handlers (set PRIMASK).

void nvic_irq_enable(nvic_irq_num irq_num)

Enable interrupt irq_num.

Parameters:

• irq_num -

  Interrupt to enable

void nvic_irq_disable(nvic_irq_num irq_num)

Disable interrupt irq_num.

Parameters:

• irq_num -

  Interrupt to disable

void nvic_irq_disable_all(void )

Quickly disable all interrupts.

Calling this function is significantly faster than calling nvic_irq_disable() in a loop.

class nvic_reg_map

NVIC register map type.

Public Members

__io uint32 ISER[8]

Interrupt Set Enable Registers.

uint32 RESERVED0[24]

Reserved.

__io uint32 ICER[8]

Interrupt Clear Enable Registers.

uint32 RSERVED1[24]

Reserved.

__io uint32 ISPR[8]

Interrupt Set Pending Registers.

uint32 RESERVED2[24]

Reserved.

__io uint32 ICPR[8]

Interrupt Clear Pending Registers.

uint32 RESERVED3[24]

Reserved.

__io uint32 IABR[8]

Interrupt Active bit Registers.

uint32 RESERVED4[56]

Reserved.

__io uint8 IP[240]

Interrupt Priority Registers.

uint32 RESERVED5[644]

Reserved.

__io uint32 STIR

Software Trigger Interrupt Registers.