Serial Ports (Serial1, Serial2, Serial3)

Used for communication between the Maple board and a computer or other devices.

Introduction

To use a serial port to communicate with an external serial device, connect the TX pin to your device’s RX pin, the RX to your device’s TX pin, and your Maple board’s ground to your device’s ground.

Warning

Don’t connect these pins directly to an RS232 serial port; they operate at +/- 12V and can damage your board.

Library Documentation

All of the Serial[1,2,3] objects are instances of the HardwareSerial class, which is documented in this section. (This means that you can use any of these functions on any of Serial1, Serial2, and Serial3).

class HardwareSerial

Serial port class. Predefined instances are Serial1, Serial2, and Serial3.

HardwareSerial::begin(unsigned int baud)

Set up a HardwareSerial object for communications. This method must be called before attempting to use the HardwareSerial object (typically, you call this in your setup() function).

HardwareSerial::end()

Disables the USART associated with this object, allowing any associated communication pins to be used for other purposes.

unsigned int HardwareSerial::available()

Returns the number of bytes available for reading.

unsigned char HardwareSerial::read()

Returns the next available, unread character. If there are no available characters (you can check this with available), the call will block until one becomes available.

HardwareSerial::flush()

Throw away the contents of the serial port’s receiver (RX) buffer. That is, clears any buffered characters, so that the next character read is guaranteed to be new.

HardwareSerial::print(unsigned char b)

Print the given byte over the USART.

HardwareSerial::print(char c)

Print the given character over the USART. 7-bit clean characters are typically interpreted as ASCII text.

HardwareSerial::print(const char* str)

Print the given null-terminated string over the USART.

HardwareSerial::print(int n)

Print the argument’s digits over the USART, in decimal format. Negative values will be prefixed with a '-' character.

HardwareSerial::print(unsigned int n)

Print the argument’s digits over the USART, in decimal format.

HardwareSerial::print(long n)

Print the argument’s digits over the USART, in decimal format. Negative values will be prefixed with a '-' character.

HardwareSerial::print(unsigned long n)

Print the argument’s digits over the USART, in decimal format.

HardwareSerial::print(long n, int base)

Print the digits of n over the USART, in base base (which may be between 2 and 16). The base value 2 corresponds to binary, 8 to octal, 10 to decimal, and 16 to hexadecimal. Negative values will be prefixed with a '-' character.

HardwareSerial::print(double n)

Print n, accurate to 2 digits after the decimal point.

HardwareSerial::println(char c)

Like print(c), followed by "\r\n".

HardwareSerial::println(const char* c)

Like print(c), followed by "\r\n".

HardwareSerial::println(unsigned char b)

Like print(b), followed by "\r\n".

HardwareSerial::println(int n)

Like print(n), followed by "\r\n".

HardwareSerial::println(unsigned int n)

Like print(n), followed by "\r\n".

HardwareSerial::println(long n)

Like print(n), followed by "\r\n".

HardwareSerial::println(unsigned long n)

Like print(n), followed by "\r\n".

HardwareSerial::println(long n, int base)

Like print(n, b), followed by "\r\n".

HardwareSerial::println(double n)

Like print(n), followed by "\r\n".

HardwareSerial::println()

Prints "\r\n" over the USART.

HardwareSerial::write(unsigned char ch)

Sends one character over the USART. This function is currently blocking, although nonblocking writes are a planned future extension.

This is a low-level function. One of the print() or println() functions is likely to be more useful when printing multiple characters, when formatting numbers for printing, etc.

HardwareSerial::write(const char* str)

Send the given null-terminated character string over the USART.

This is a low-level function. One of the print() or println() functions is likely to be more useful when printing multiple characters, when formatting numbers for printing, etc.

HardwareSerial::write(void* buf, unsigned int size)

Writes the first size bytes of buf over the USART. Each byte is transmitted as an individual character.

This is a low-level function. One of the print() or println() functions is likely to be more useful when printing multiple characters, when formatting numbers for printing, etc.

Arduino Compatibility Note

Unlike the Arduino, none of the Maple’s serial ports is connected to the USB port on the Maple board. If you want to communicate using the built-in USB port, use SerialUSB instead. You will need an additional USB-to-serial adapter to communicate between a USART and your computer.

License and Attribution

Portions of this page were adapted from the Arduino Reference Documentation, which is released under a Creative Commons Attribution-ShareAlike 3.0 License.